 | Prince Heavy Duty Hydraulic Motor - 14 GPM, 1800 PSI, Model# ADM200-4RP
Brand: Prince
For light and medium duty applications. Replacement for Charlynn H, White HS, and Ross TRW MG series. Maximum inlet pressure is 2500 PSI and maximum back pressure is 1000 PSI. Fully reversible, 4-bolt mount with 1in. x 1 3/4in. shaft with 1/4in. keyway. 1/2in. NPTF ports. Orbiting Gerotor Principle. | *$299.99 |
| Prince Heavy Duty Hydraulic Motor - 14 GPM, 2000 PSI, Model# ADM100-4RP
Brand: Prince
For light and medium duty applications. Replacement for Charlynn H, White HS, and Ross TRW MG series. Maximum inlet pressure is 2500 PSI and maximum back pressure is 1000 PSI. Fully reversible, 4-bolt mount with 1in. x 1 3/4in. shaft with 1/4in. keyway. 1/2in. NPTF ports. Orbiting Gerotor Principle. | *$279.99 |
 | Prince PTO Tractor Pump 23 GPM, Model# HC-PTO-3A
Brand: Prince
Gear-type, heavy-duty pump is designed for PTO drive operation on tractors of all sizes. No additional gearing is required. These pumps feature self-adjusting wear plates that seal off leakage and offset any wear or expansion that may occur during the life of the pump. High tensile aluminum housing, minimum gear clearance, cast iron endplates. Internal splined shafts go all the way through and are supported on both sides by roller bearings. All models have a #16 SAE inlet port and two #12 SAE outlet ports. Include #12 SAE to 3/4in. NPTF female adapter. Reservoir size should at least be as large as the output of the pump. | *$484.99 |
 | Prince PTO Tractor Pump 40 GPM, Model# HC-P-K11
Brand: Prince
At 1000 PSI, direct drive pump delivers 40.1 GPM at 1000 RPM and over 20 GPM at 540 RPM. Pump has roller bearing construction, pressure balanced self-adjusting wear plates and an internally splined drive shaft, 1 3/8in.-21 tooth, so it needs no gear box. Handles pressures up to 2250 PSI. SAE O-ring ports: inlet #20 1 5/8in.-12, drain outlet #16 15/16in.-12, plus auxiliary outlet, #12 11/16in.-12. Includes #20 SAE to 2in. hose adapter and #16 SAE to 1in. female pipe. Easy installation using torque arm restraint. Reservoir size should at least be as large as the output of the pump. U.S.A. | *$499.99 |
 | Prince Standard 3-Way Control Valve, Model# RD-2575-T3-ESA1
Brand: Prince
A control valve for operating single-acting cylinders. This valve has 3 ports, 3-position spring center to neutral and adjustable relief valve. Relief valve preset at 1500 PSI, adjusts up to 3000 PSI. Convertible from open to closed center. 3/4in. in/out ports, 1/2in. working ports. U.S.A. | *$109.99 |
 | Prince Tie-Rod Cylinder - 2500 PSI, 3in. Bore, 8in. Stroke, 1 1/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 2500 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 2,500, Bore Diameter (in.): 3, Stroke Length (in.): 8, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 1 1/8 | *$149.99 |
| Prince Tie-Rod Cylinder - 2500 PSI, 4in. Bore, 8in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 2500 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 8, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 2 | *$229.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 2 1/2in. Bore, 12in. Stroke, 1 1/4in. Shaft
Brand: Northern Tool Equipment
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 2 1/2, Stroke Length (in.): 12, Closed Pin Center (in.): 22 1/4, Shaft Diameter (in.): 1 1/4 | *$159.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 2 1/2in. Bore, 16in. Stroke, 1 1/4in. Shaft
Brand: Northern Tool Equipment
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 2 1/2, Stroke Length (in.): 16, Closed Pin Center (in.): 31 1/2, Shaft Diameter (in.): 1 1/4 | *$169.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 2 1/2in. Bore, 24in. Stroke, 1 1/4in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 2 1/2, Stroke Length (in.): 24, Closed Pin Center (in.): 34 1/4, Shaft Diameter (in.): 1 1/4 | *$179.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 2in. Bore, 12in. Stroke, 1 1/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 2, Stroke Length (in.): 12, Closed Pin Center (in.): 22 1/4, Shaft Diameter (in.): 1 1/8 | *$139.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 2in. Bore, 18in. Stroke, 1 1/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 2, Stroke Length (in.): 18, Closed Pin Center (in.): 28 1/4, Shaft Diameter (in.): 1 1/8 | *$149.99 |
 | Prince Tie-Rod Cylinder - 3000 PSI, 2in. Bore, 20in. Stroke, 1 1/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 2, Stroke Length (in.): 20, Closed Pin Center (in.): 30 1/4, Shaft Diameter (in.): 1 1/8 | *$159.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 3 1/2in. Bore, 10in. Stroke, 1 3/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 10, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 1 3/8 | *$179.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 3 1/2in. Bore, 12in. Stroke, 1 3/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 12, Closed Pin Center (in.): 22 1/4, Shaft Diameter (in.): 1 3/8 | *$189.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 3 1/2in. Bore, 18in. Stroke, 1 3/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 18, Closed Pin Center (in.): 28 1/4, Shaft Diameter (in.): 1 3/8 | *$199.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 3 1/2in. Bore, 8in. Stroke, 1 3/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 8, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 1 3/8 | *$169.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 3in. Bore, 16in. Stroke, 1 3/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3, Stroke Length (in.): 16, Closed Pin Center (in.): 31 1/2, Shaft Diameter (in.): 1 3/8 | *$179.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 3in. Bore, 18in. Stroke, 1 3/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3, Stroke Length (in.): 18, Closed Pin Center (in.): 28 1/4, Shaft Diameter (in.): 1 3/8 | *$189.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 3in. Bore, 24in. Stroke, 1 3/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 3, Stroke Length (in.): 24, Closed Pin Center (in.): 34 1/4, Shaft Diameter (in.): 1 3/8 | *$229.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 4 1/2 in. Bore, 24in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4 1/2, Stroke Length (in.): 24, Closed Pin Center (in.): 36 1/4, Shaft Diameter (in.): 2 | *$359.99 |
 | Prince Tie-Rod Cylinder - 3000 PSI, 4in. Bore, 10in. Stroke, 1 3/4in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4, Stroke Length (in.): 10, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 1 3/4 | *$229.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 4in. Bore, 12in. Stroke, 1 3/4in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4, Stroke Length (in.): 12, Closed Pin Center (in.): 22 1/4, Shaft Diameter (in.): 1 3/4 | *$229.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 4in. Bore, 16in. Stroke, 1 3/4in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4, Stroke Length (in.): 16, Closed Pin Center (in.): 31 1/4, Shaft Diameter (in.): 1 3/4 | *$249.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 4in. Bore, 30in. Stroke, 1 3/4in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4, Stroke Length (in.): 30, Closed Pin Center (in.): 40 1/4, Shaft Diameter (in.): 1 3/4 | *$299.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 4in. Bore, 36in. Stroke, 1 3/4in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 4, Stroke Length (in.): 36, Closed Pin Center (in.): 46 1/4, Shaft Diameter (in.): 1 3/4 | *$319.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 16in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 16, Closed Pin Center (in.): 31 1/2, Shaft Diameter (in.): 2 | *$349.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 18in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 18, Closed Pin Center (in.): 30 1/4, Shaft Diameter (in.): 2 | *$349.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 24in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 24, Closed Pin Center (in.): 36 1/4, Shaft Diameter (in.): 2 | *$389.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 30in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 30, Closed Pin Center (in.): 42 1/4, Shaft Diameter (in.): 2 | *$379.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 8in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 8, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 2 | *$269.99 |
 | Prince Welded Tee Cylinder - 2500 PSI, 2 1/2in. Bore, 12in. Stroke, 1 3/8in. Shank, Model# PMC-5412
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 2 1/2, Stroke Length (in.): 12, Closed Pin Center (in.): 20, Shaft Diameter (in.): 1 3/8 | *$159.99 |
 | Prince Welded Tee Cylinder - 2500 PSI, 2 1/2in. Bore, 8in. Stroke, 1 3/8in. Shaft, Model# PMC-5408
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All-steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 2 1/2, Stroke Length (in.): 8, Closed Pin Center (in.): 16, Shaft Diameter (in.): 1 3/8 | *$149.99 |
| Prince Welded Tee Cylinder - 2500 PSI, 3 1/2in. Bore, 36in. Stroke, 1 1/2in. Shaft, Model# PMC-5536
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3 1/2, Stroke Length (in.): 36, Closed Pin Center (in.): 44, Shaft Diameter (in.): 1 1/2 | *$259.99 |
| Prince Welded Tee Cylinder - 2500 PSI, 3in. Bore, 36in. Stroke, 1 1/2in. Shaft, Model# PMC-8336
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3, Stroke Length (in.): 36, Closed Pin Center (in.): 44, Shaft Diameter (in.): 1 1/2 | *$269.99 |
| Prince Welded Tee Cylinder - 2500 PSI, 3in.Bore, 12in. Stroke, 1 1/2in. Shaft, Model# PMC-8312
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3, Stroke Length (in.): 12, Closed Pin Center (in.): 20, Shaft Diameter (in.): 1 1/2 | *$174.99 |
 | Prince Welded Tee Cylinder - 2500 PSI, 3in.Bore, 8in.Stroke, 1 1/2in. Shaft, Model# PMC-8308
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 3, Stroke Length (in.): 8, Closed Pin Center (in.): 16, Shaft Diameter (in.): 1 1/2 | *$159.99 |
| Prince Welded Tee Cylinder - 2500 PSI, 4in. Bore, 16in. Stroke, 2in. Shaft, Model# PMC-5616
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 16, Closed Pin Center (in.): 25, Shaft Diameter (in.): 2 | *$249.99 |
| Prince Welded Tee Cylinder - 2500 PSI, 4in. Bore, 20in. Stroke, 2in. Shaft, Model# PMC-5620
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 20, Closed Pin Center (in.): 29, Shaft Diameter (in.): 2 | *$269.99 |
| Prince Welded Tee Cylinder - 2500 PSI, 4in. Bore, 36in. Stroke, 2in. Shaft, Model# PMC-5636
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 36, Closed Pin Center (in.): 45, Shaft Diameter (in.): 2 | *$319.99 |
| Prince Welded Tee Cylinder - 2500 PSI, 4in. Bore, 48in. Stroke, 2in. Shaft Size
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 48, Closed Pin Center (in.): 58, Shaft Diameter (in.): 2 | *$419.99 |
 | PUMP FOOTAIR/HYDRAULIC 10 TON
Brand: Neiko Part Number: RI-50622 | *$244.70 |
 | Red Lion Cross-Tube Welded Hydraulic Cylinder - 3000 PSI, 3in. Bore, 8in. Stroke, 1 1/2in. Shaft, Model# 30WX08-150
Brand: Red Lion
Ideal for high- or low-pressure industrial or construction applications. Cross-tube welded cylinder operates at 3000 PSI with a 6000 PSI proof pressure rating. Ports are 3/4-16 UNF ORB and are 90deg to pins. Cap and cross tube ends are durable steel cast components made to withstand continuous high loads. Precision finished skived and burnished heavy wall steel tubing for extended seal and cylinder life. Max. PSI: 3,000, Bore Diameter (in.): 3, Stroke Length (in.): 8, Shaft Diameter (in.): 1 1/2 | *$169.99 |
 | Red Lion Welded Cylinder - 2500 PSI, 24in. Stroke, Model# 40WC24-200
Brand: Lion 2500
2in. chrome rod, crown piston seals with wear ring, hallite rod seals and wear ring, single lug base end and drilled pin rod end. | *$269.99 |
 | Red Lion Welded Double-Acting Cylinder - 2500 PSI, 36in. Stroke, Model# 25WC36-150
Brand: Red Lion
Excellent for loaders, engine hoists and small boom conveyors. 1 1/2in. chrome rod, crown piston seals with wear ring, hallite rod seals, cross tube base end and threaded end. Complete with ductile threaded rod clevis, one pin and retaining clips. | *$229.99 |
 | Replacement Pump for 4 Ton Capacity Porta Power Set (MTN5405)
Brand: Mountain Part Number: 5405
Item #: MTN5405. brCustomers also search for: Discount Replacement Pump for 4 Ton Capacity Porta Power Set, Buy Replacement Pump for 4 Ton Capacity Porta Power Set, Wholesale Replacement Pump for 4 Ton Capacity Porta Power Set, 613364025680, ToolWeb, Porta Powers and Pumps | *$76.31 |
 | Rotary Pump Drip Tray With Hinged Cover
Brand: Global Industrial Part Number: DRIPTRAY
DRIP TRAY FOR ROTARY PUMP Drip tray returns spills into drum, reducing waste and cleanup. Cast iron and steel construction with hinged cover and 2" bung adapter. | *$35.95 |
 | Ryton Rotary Pump For Aggressive Chemicals
Brand: Global Industrial Part Number: 10212
Rotary Drum Pump - Ryton Ryton construction with ryton vanes, viton oil seal and teflon flange gaskets. Used for aggressive chemicals such as chlorinated solvents and hydrocarbons. Not recommended for ketones and ethers and very strong oxidizing agents in concentrated form. Dispenses 8 oz. per revolution. Includes 2" bung adapter, 3 piece 14"dia. x 44"L suction tube with strainer and 1" discharge spout. | *$82.95 |
 | St106 Flange Pins2 Per (432-780430) Category: Hydraulic Tool Parts
Brand: Sumner Model: 780430 Part Number: 780430
Item #: 432-780430. Quick installing pins work as convenient reference points to level flange for tack and weld out - no tools neededbrFeatures acme threads for maximum clamping power and hardened steel for long lasting use pulliOperating Face Hole Diameter = 5/8 in [Min], 1 5/8 in [Max]liInside Wt. = 4 lb/ul brCustomers also search for: Discount St106 Flange Pins2 Per, Buy St106 Flange Pins2 Per, Wholesale St106 Flange Pins2 Per, 661165804300, 780430, Hydraulic Tool Parts and Accessories | *$80.99 |
 | Standard Half Coupling - 1 1/8in. Size
Brand: Northern Tool Equipment
Use a flex coupling to direct-mount your engine to pump. Oil-resistant synthetic rubber inserts are used between the coupling halves to provide an equalized cushioned drive. When ordering, get one side to fit the motor and the other side to fit the pump shaft dia. Order two halves plus insert for complete coupling. When mounting, do not pound on the end of your pump shaft. U.S.A. Shaft Diameter (in.): LO95 HUB 1 1/8, Fits Models: LO90, LO95, Max. HP: 11.16, Max. Torque (in.-lbs.): 194, Max. RPM: 3,600, Material Type: Synthetic Rubber, Keyway (in.): 1/4 x 1/8 | *$15.99 |
|
